Powerglide Tappet - .002 - Twin Cam The same Powerglide advantage (oil-fed axle, billet steel body, precision fit hydraulics), but now incorporates a Steady Roll bronze bushing in place of the needle bearing roller, These tappets have undergone extensive...

Bolt Case - Big Bore - Twin Cam Prevents center right case bolt thread from becoming compromised from larger cylinder spigot bore diameter, Tool is needed to spot face the right case so bolt head will seat flat on case surface, Center-through bolt kit...

Clutch Hub Puller - '36-'90 Big Twin Used to remove wet and dry clutch hubs without removing clutch release rod, 4 bolts included for dry clutch removal, Made in the U.S.A.

Wheel Bearing Locknut Tool - XL Use to remove and install the slotted locknut to the correct torque on spoke wheels, Made in the U.S.A.

Socket - Pin Shaft - Nut - Big Twin Machined for 100% nut-to-socket and drive-end contact, Eliminate nut rounding and risk of injury, Made in the U.S.A.

Main Drive Gear Tool - 5th Gear/Inner/Outer Used to install inner and outer 5th gear bearings to factory depth

JIMS Mainshaft

Valve Spring Kit - Evolution - Big Twin Incorporate an interference double-spring design with a damper to control harmonics, Engineered for maximum performance in severe applications such as high compression and big-inch street motors, Kits include...

Facer Tool - Case - Twin Cam Prevents center right case bolt thread from becoming compromised from larger cylinder spigot bore diameter, Tool is needed to spot face the right case so bolt head will seat flat on case surface, Made in the U.S.A.

Torque Plate - Twin Cam '99-'17 - 4" Torque plates must be used when boring or honing late-model aluminum cylinders, Simulate running stress conditions, Come with instructions, Made in the U.S.A.

Valve Seal Installer - 110" Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals, Made in the U.S.A.

Alignment Tool - Powertrain Alignment service must be performed when engine, transmission or swingarm has either been removed or repaired, Safety in handling and performance could be greatly affected without the accurate alignment this tool provides,...

Clutch Assembly Tool - '90-'16 Big Twin Safely removes and installs clutch shell ball bearing without any damage to new bearing by pushing on the outer perimeter of bearing, Safely disassembles and assembles clutch shell assembly, Easily removes and...

Socket - Fork Compression - Indian For use on Indian Scout models, Made in the U.S.A.

Roller Rocker Bushing - 8 pack For repairing roller rockers that use Torrington roller bearings, Press fit and line ream to H-D specifications, Works in Crane roller rocker arms, Made in the U.S.A.

Gauges - Camshaft Bearing - Go and No-Go* The only accurate and easy way to check the size of the inside diameter of the inner cam bearing, Use these gauges to check whether the cam will be too loose or too tight, Made in the U.S.A.

Bolt Kit - Torque Plate - Evolution XL Torque plates must be used when boring or honing late-model aluminum cylinders, Simulate running stress conditions, Come with instructions, Made in the U.S.A.

Lower Cord - HS269, 374, 477 Fit a wide variety of J&M headsets as well as Drag Specialties headsets from J&M, Cords feature top-quality connectors, Made in the U.S.A.

Lower Cord - GL '83-'04 Interchanging 8-pin lower-section hook-up cords for the P-series two-piece cord system, Allows P-Series headsets to be connected to any factory-installed motorcycle audio system, Made in the U.S.A.

Lower Cord - Yam/Kaw/Suz '83-'04 Interchanging 8-pin lower-section hook-up cords for the P-series two-piece cord system, Allows P-Series headsets to be connected to any factory-installed motorcycle audio system, Made in the U.S.A.