Transmission Tools

DRAG SPECIALTIES Starter Jackshaft Lock Tool 3802-0071Slides over the shaft, allowing you to loosen the bolt to remove the jackshaft assembly when switching out starters or removing the inner primary, Holds the jackshaft by the splines without damaging...

DRAG SPECIALTIES Transmission Sprocket Nut Wrench 131141-HC4Also features a 1/2" drive for use with a ratchet or torque wrench, Necessary for removing transmission sprocket locknut

JIMS 6-Speed Main Gear Installation and Remover Tool 900Complete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson­­® 6-speed transmission, Tool removes and installs both parts correctly without damaging the case

JIMS Sprocket Nut Socket Tool XL 5516Ensures the mainshaft on Harley-Davidson® Sportster models extend through the guidance collar for correct alignment, Short socket is specifically designed to remove, install and properly tighten the front final drive...

JIMS Shift Sleeve Tool Big Twin 5517A real time saver for removing and installing the shifter mechanism sleeve in Cruise Drive Big Twin transmissions, Tool allows you to remove and install the sleeve (bushing) without having to disassemble the...

JIMS Shift Pedal Shaft Tool 5518Time-saving tool removes worn shift shaft bushings in Big Twin primaries without having to remove he inner primary, Tools installs new bushings to the correct location, Made in the U.S.A.

JIMS Compensator Bolt Socket Tool 14-Bit 5534Correct style driver/socket for the compensating sprocket retaining fastener, Made in the U.S.A.

JIMS Countershaft 1 Gear Alignment Tool M8 5816Maintains alignment of gear halves under spring pressure, Ensures scissor gear teeth line up with mainshaft, Essential for installing M-Eight transmissions, Made in the U.S.A.

JIMS Tool Primary Locking 04-19XL 5520Immobilizes primary drive, Allows for tightening with a torque wrench or loosening with a breaker bar, Prevents damage to rotor or magnets sometimes caused by air-wrench, Made in the U.S.A.

JIMS Puller Trap Door '80-'06 Big Twin 1014Used to remove and install bearings on 5-speeds and aftermarket 6-speeds, Can also be used to pull trapdoors on 5-speeds and aftermarket 6-speeds, Housing bearings must be replaced when pulling door, Made in the...

JIMS Primary Lock Bar 91-08 XL 2318Immobilizes primary drive, Allows for tightening with a torque wrench or loosening with a breaker bar, Prevents damage to rotor or magnets sometimes caused by air-wrench, Made in the U.S.A.

JIMS Tool Sealed Wheel Bearing 939Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking Brake System (ABS), Made in the U.S.A.

JIMS 5 Speed Main Seal Installer Tool 2268Ensures correct alignment, seal protection and depth when installing the seal, Made in the U.S.A.

JIMS Bearing Remover Plate Tool 967-5Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing, Also removes and installs inner primary bearing and seal that transmission mainshaft passes...

JIMS Bearing Remover Plate Tool 967-4Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing, Also removes and installs inner primary bearing and seal that transmission mainshaft passes...

JIMS Inner Primary Seal/Bearing Tool 729Gives a much better feel than a press while eliminating the possibility of applying too much pressure to the parts, Provides precise installation and eliminates the cumbersome task of performing the installation in...

JIMS 5 and 6 Speed Center Shaft Tool 739Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without using a press or tapping it in with a transmission shaft, Designed to install the bearing squarely and to the...

JIMS Shift Shaft Sleeve Tool 1658Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum, Use to install shifter shaft sleeve, Made in the U.S.A.

JIMS 5-Speed Shift Seal Installer Tool 768Makes installing shifter shaft seal precise and effortless, Aligns, centers and installs shifter seal to correct depth, Made in the U.S.A.

JIMS 6-Speed Shaft Seal Installer Tool 767Makes installing shifter shaft seal precise and effortless, Aligns, centers and installs shifter seal to correct depth, Made in the U.S.A.