Harley Engine Tools

JIMS XL Clutch Spring Tool 84-90 34761-84Use to release the clutch spring tension for disassembly, Made in the U.S.A.

JIMS Bearing Simulator 70-99 Big/Twin 1745Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or cylinder-to-flywheel clearance, Will not mar bearing...

JIMS Crankshaft Guide 99-17 Twin Cam 1288Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly, Made in the U.S.A.

JIMS Sprocket Shaft Bearing Tool Big Twin 1709This tool will remove the sprocket shaft Timken® bearing on late Big Twins, 1986-present, with an integral sprocket shaft, Does the job better than anything else on the market, Made in the U.S.A.

JIMS Sprocket Shaft Installer 95-03 2324Installs sprocket seal to proper depth, Use with JIMS® Driver Handle, Holds seal perfectly square, Made in the U.S.A.

JIMS Timken® Bearing Race Installer 2246Used to install bearing race straight into the left crankcase, A must for late-model cases, Made in the U.S.A.

JIMS Tappet Oil Filter Plug Tool 2233Used to remove the tappet oil screen plug, Removes oil screen without removing exhaust, Made in the U.S.A.

JIMS Valve Guide Driver Tool Set 1001Designed for guide removal and installation on all models, Made in the U.S.A.

JIMS Shift Pawl Plate Assembly 85-00 Big Twin 2384Assembly includes plate, spring, pawl plate, shifter shaft, spring, pin, washer and retaining ring, Reduces shifter free play, Made in the U.S.A.

JIMS Shift Adjuster 80-00 5-Speed 33119-79AHigh-quality OEM replacement component, Made in the U.S.A.

JIMS Shovelhead Clean-Up Kit 1046Meticulously engineered valve train kit enables Evolution-style oiling of your Shovelhead top-end, Allows removal of stock Shovelhead top-end oiling system, Top-end is oiled through JIMS proven Powerglide™ tappets, then...

JIMS V-Twin Rod Holder 1284Use to keep connecting rods in place and eliminate twisting or bending of the connecting rod while reaming or honing the wrist pin bushings, Made in the U.S.A.

JIMS Twin Cam Rod Alignment Tool 1148Use to check rod straightness without removing the rods from the cases, Made in the U.S.A.

JIMS Clutch Hub Puller 1004ACan be used on 3-, 5- or 10-finger clutch hubs and 45" clutch hubs, Will also work on Big Twin motor sprocket, alternator cover and early XL clutches as well as many other applications, Made in the U.S.A.

JIMS 4-Speed Seal Driver 82-86 Big Twin 95660-77Optional drivers used in conjunction with main shaft seal tool allow installation of seals

JIMS Fork Nut Socket 35 mm 3/8" 2244Used to remove and install top fork nuts on fork tubes, Rubber protector inside socket, Will clear most handlebars, Made in the U.S.A.

JIMS Wristpin Bush. Reamer73-99 1726-1Used to ream wrist pin bushings to the proper inner diameter, Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications)., Can be used with rods in or...

JIMS Wrist Pin Reamer 57-18Xl 1726-2Used to ream wrist pin bushings to the proper inner diameter, Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications)., Can be used with rods in or...

JIMS Tool Camshaft Bearing Installation 99-17 Twin Cam 787Use to install the two inner cam bearings, Designed to press from the letter side of the inner cam bearing to eliminate any damage to the bearings, cam or case, Will set bearings .023"-.028" below...

JIMS Tool Camshaft Bearing Installation 99-17 1278-3Replacement drive for JIMS® Cam Bearing Installation Tool