Harley Engine Tools

JIMS Rocker Bush Remover 66-17 Twin Cam 94804-57This precise line reamer is capable of a 24 finish or better, Use to ream rocker bushings to a factory fit of .0007” - .0012” in line with each other, Made in the U.S.A.

JIMS Pinion Bushing Line Reamer 54-97 Big Twin 94805-57Designed to line-ream pinion bushing in cam cover from right case race, Use on all Big Twin 1954-99 single cam only, (NOTE: Includes aftermarket motors, also XL 1957 to early 1984 idler gear...

JIMS Cam Bushing Installer 1012-70TBUse to install bushing and drill dowel pin hole to factory specification, #31 jobber length HSS drill bit included with jigs, Use staking dowel pin, Made in the U.S.A.

JIMS Pin Bushing Installer 1013-54TBUse to install bushing and drill dowel pin hole to factory specification, #31 jobber length HSS drill bit included with jigs, Use staking dowel pin, Made in the U.S.A.

JIMS Cam Bushing Installer 1017-37TBUse to install bushing and drill dowel pin hole to factory specification, #31 jobber length HSS drill bit included with jigs, Use staking dowel pin, Made in the U.S.A.

JIMS Crank Pin Nut Socket 83-99 Big Twin 1030-TSMachined for 100% nut-to-socket and drive-end contact, Eliminate nut rounding and risk of injury, Made in the U.S.A.

JIMS Motor Stand 99-17 Twin Cam A Engine 1022Make working on motors easier with better access, Made in the U.S.A.

JIMS Neck Tool Driver Spacer 2388Removes and installs steering head bearing race on 84-16 Big Twin (except 14-16 Dressers), 86-16 XL and 94-02 Buell OEM frames (will also work on most aftermarket frames), Must be used with tool driver spacer and...

JIMS Valve Spring Compressor Tool Harley-Davidson® 96600-36BThis tool is necessary for removing or installing valves, Hardened ball bearing style tip at valve head end eliminates damage to valve, Comes with new valve collar receiver for safer tool usage,...

JIMS Handle Only for/Road/Race Tools 33416-80Easy-to-use race installer/remover handle by JIMS®, Use with JIMS® Bearing Race Tools, Made in the U.S.A.

JIMS Camshaft Bearing Tool 57-90 XL 97273-60Use to install inner cam bearings, Made in the U.S.A.

JIMS Camshaft Bearing Tool 58-99 Big Twin 97272-60Use to install inner cam bearings, Made in the U.S.A.

JIMS Sprocket Shaft Bearing Race Tool 94547-80BUsed to remove and install Timken® bearing race on motor cases, Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042), Made in the U.S.A.

JIMS Electronic Speedometer Sensor '00-'06 Softail 74437-96Top-quality replacement sensor, Also works on any aftermarket transmission case with a speedometer sensor hole, Includes O-ring, hardware and OEM connector, Made in the U.S.A.

JIMS Electronic Speedometer Sensor '99-'03 FLT 74420-94Top-quality replacement sensor, Also works on any aftermarket transmission case with a speedometer sensor hole, Includes O-ring, hardware and OEM connector, Made in the U.S.A.

JIMS Tool Pushrod Cover Clip Remover/Installer 917Will install the clip professionally with just one hand in seconds, This tool will NOT marr or slip, Made in the U.S.A.

JIMS Tool Pilot Valve Guide 7Mm 2240-19Adapters are supported by a stand that makes it easy to press valve guides in and out, Adapters for working on 7 mm valve guides, Made in the U.S.A.

JIMS Tool Insert Valve Guide 7Mm 2240-11-4Adapters are supported by a stand that makes it easy to press valve guides in and out, Adapters for working on 7 mm valve guides, Made in the U.S.A.

JIMS Wrist Pin Bushing Twin Cam 3998KMachined from solid bronze bar stock, Hold concentricity to less than .0002", Lead-in edge for easy installation, Made in the U.S.A.

JIMS Alternator Rotor Puller 1147A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes, Tool protects threads on sprocket shaft from damage while pulling rotor free from its...