Harley Engine Tools

JIMS Tool Balancer Scissor Gear M8 5811For use on the Milwaukee Eight™ engine series, Holds 2 halves of spring-loaded balancer scissor gear in alignment before removal, Bright color reminds technician to remove it before sealing engine case

JIMS Rotor Alternator Tool M8 5812For use on the Milwaukee Eight™ engine series, Removes rotor while protecting magnets, Made in the U.S.A.

JIMS Main Bearing Remover and Installer Tool M8 5813Main bearing remover and installer designed just for the Milwaukee Eight®, High levels of precision and accuracy are necessary, so only the best tools can be trusted, Not only removes the left and right...

JIMS Flywheel Lock Tool M8 5823For use on the Milwaukee Eight™ engine series and all Twin Cam motors, This tool is designed to lock the crankshaft when doing service work, Just take out the crank position sensor and install the “Mighty Bite” into the...

JIMS Valve Spring Tool '05-'17 988For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013), Made in the U.S.A.

JIMS Tool Camshaft Assembly 07-17 Twin Cam 990Holds both cams in an upright position while lowering cam support plate over both guides and cam journal guides, Made from a non-marring material that will not damage any of the cams' surfaces, Made in the U...

JIMS Tool Case Bearing Conversion Twin Cam 959Included in kit is one new steel bearing insert sleeve (held to under .0002" total indicator reading), all necessary drill bits to drill oil feed and return holes, press plate that holds bearing sleeve insert...

JIMS Tool Balance Shaft 07-08 Softail 960Designed for the 96" and 110" Beta® engines, Removes both the front and rear counter-balancer shaft bearing assembly, from the left engine case, Made in the U.S.A.

JIMS Tool Bearing Puller 03-17 Twin Cam 963Can also be used to remove Timken® bearing pinion shaft inner bearing race on 57-07 XL, including all Buells®, and used to remove press-fit transmission gears and bearings from input and output shafts on all...

JIMS Piston Pin Bush Tool All Model 95970-32CUse to remove and install wrist pin bushings without removing rods from crankcase, Made in the U.S.A.

JIMS Shift Fork Gauge 4-Speed 79-86 Big Twin 96385-78AThis tool checks alignment of Big Twin transmission shift forks, Made in the U.S.A.

JIMS Shift Fork Gauge 39-78 Big Twin 96384-39This tool checks alignment of Big Twin transmission shift forks, Made in the U.S.A.

JIMS Piston Pin Lock Ring Tool Pre-73 Big Twin 96780-58AUse to install lock ring (Harley-Davidson® No. 22582-52) in piston having .515” inner diameter wrist pins, like most aftermarket pistons, This tool will install “spiral lock” rings in one easy step...

JIMS Sprocket Shaft Bearing Nut Tool 55-68 97235-55BUsed to install and remove bearing nut, Made in the U.S.A.

JIMS Pinion Gear Puller Evolution/Shovelhead 96830-51Use to install pressed on splined pinion gears on Harley-Davidson® Big Twin, Also can be used to remove pinion gear on Big Twin's and Sportsters, Made in the U.S.A.

JIMS Main Drive Gear Seal/Bearing Tool 34734-80Holds bearings and seal square to its bore, eliminating any marring, Install both bearings and seal with use of a 1-ton press, Install bearings and seal to correct depth, Made in the U.S.A.

JIMS Piston Pin Tool 83-99 Evolution 34623-83This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention possible, Use to install retaining ring in piston, Made in the U.S.A.

JIMS Main Drive Gear Bearing Tool 4-Speed 33428-78Use to install the main bearing (Harley-Davidson® #8905) to the correct depth, Made in the U.S.A.

JIMS Valve Guide Remover Tool Evolution 34740-84Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals, Made in the U.S.A.

JIMS Evolution Valve Guide Installer Tool 34731-84Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals, Made in the U.S.A.