Harley Engine Tools

JIMS Evolution Valve Seal Installer Tool 34643-84Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals, Made in the U.S.A.

JIMS Engine Stand for/57-99 XL 1007Make working on motors easier with better access, Made in the U.S.A.

JIMS Crank Assembly Removal Tool 55+ Big Twin 1047-TPUse to press flywheels from cases, Will also press cases apart and break sealant bond, Some case pressing will require a hard cap, This tool can only be used for removing the flywheel from the left...

JIMS Camshaft Cover Holder Tool 70-99 Big Twin 1041-TCHolds cam cover flat and helps prevent damage/scratches when removing and installing bushings, Clamps in vice or Bridgeport™ mill, Made in the U.S.A.

JIMS Pinion Nut Socket 55-92 Big Twin 94555-55AUse to remove or secure pinion gear nut to pinion gear shaft, Made in the U.S.A.

JIMS Center Shift Locknut 94660-37ARemove hex nut from end of main drive gear that secures the rear drive transmission pulley, Inner collar will retain wrench to nut for safer work, Extra-long two-piece design, Made in the U.S.A.

JIMS Transmission Access Cover Tool 54-85 Big Twin 95560-57Use to remove transmission access covers, which are press-fit on two dowel pins, Made in the U.S.A.

JIMS Sprocket Shaft Bearing Race Tool 94547-80AUsed to remove and install Timken® bearing race on motor cases, Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042), Made in the U.S.A.

JIMS Sprocket Shaft Seal Installation Tool 39361-69Designed to press oil seal over sprocket shaft into case, Made in the U.S.A.

JIMS Sprocket Shift Bearing Installation Tool 97225-55Used on 84-02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing, Made in the U.S.A.

JIMS 2.5" Sleeve Only for/196052 37047-91-6For use on specific Harley-Davidson® Sportster and Buell® model years, Optional sleeves for JIMS® Sprocket Shaft Bearing Installation Tool, Both optional sleeves are required to install the sprocket bearing

JIMS Sprocket Shaft Bearing Press Tool 97081-54Use on 55-76 XL and K models to install the flywheel assembly into the left crankcase Timken® bearing, Optional sleeves sold separately for use on 86-03 XL and 94-03 Buell, Made in the U.S.A.

JIMS 2.060" Sleeve Only for/196052 37047-91-5For use on specific Harley-Davidson® Sportster and Buell® model years, Optional sleeves for JIMS® Sprocket Shaft Bearing Installation Tool, Both optional sleeves are required to install the sprocket bearing

JIMS Transmission Gear Spacing Tool XL 35820-86Used to align main and countershafts when checking proper gear spacing, Made in the U.S.A.

JIMS Mainshaft Bearing Race Tool Big Twin 34902-84Used to remove and install the inner bearing race on the transmission mainshaft, Made in the U.S.A.

JIMS Engine Stand 84-99 Evolution Big Twin 1006TMake working on motors easier with better access, Made in the U.S.A.

JIMS Clutch Spring Compressor 71-84 XL 97178-71Used to remove or install clutch components, Made in the U.S.A.

JIMS Neck Race Remover Tool 2232Removes and installs steering head bearing race on 84-16 Big Twin (except 14-16 Dressers), 86-16 XL and 94-02 Buell OEM frames (will also work on most aftermarket frames), Must be used with tool driver spacer and...

JIMS Camshaft Pinion Gauge Pins 108 1111Use to check pinion gear for pitch diameters, Check service manual for sizing chart, Made in the U.S.A.

YOST PERFORMANCE Intake Manifold Wrench 84-06 WRNBCuts the work time in half, Remove only the carburetor, no need to remove the gas tank, Made in the U.S.A. by Yost Performance