Harley Engine Tools

JIMS Tool Tester Tappet Twin Cam 765Helps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won't pump up due to poor hydraulic unit fitment, Allows filling of hydraulic tappets before assembling...

JIMS Engine Stand 00-17 Twin Cam Beta 902Make working on motors easier with better access, Made in the U.S.A.

JIMS Tool Reamer Valve Guide 7Mm 1133Quality pilot lead-in reamer, For 7 mm valve guides Harley-Davidson® No. 16461-02 that are used in conjunction with the latest conical (Beehive) valve springs, Will also work on equivalent aftermarket 7 mm valve...

JIMS Tool Valve Spring Tester 1090Works with bench vise, arbor, screw hydraulic or drill press, Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter, 0 to 1000 P.S.I. gauge, Made in the U.S.A.

JIMS Tool Seal Leak Tester 780Required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases horsepower from oil drag, Can also be used to check pressure lost at the...

JIMS Tool Balancer Retainer 779Holds hydraulic tensioners in place that keep constant chain tension on counter balancer system, Made in the U.S.A.

JIMS Tool Seal Installation 6 Speed 06-16 786Harley-Davidson’s® new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made, JIMS® has developed a driver style seal installer (not a pushing or pulling...

JIMS Tool Cylinder Leakdown 4-Stroke 782Tool troubleshoots cylinder leakdown issues such as valve seat issues, bad rings and bad head gasket, Hose assembly has both 14 mm and 18 mm spark plug threads, Includes 12 mm and 10 mm adapter, Made in the U.S.A.

JIMS Tool Piston Ring Cpompressor Kit 910Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression, Will not break or damage rings, Made in the U.S.A.

FEULING OIL PUMP CORP. Tool Push Rod Tube Holder 9012Makes for easy adjustment of adjustable pushrods, holding pushrod tubes up and out of the way, Made in the U.S.A.

JIMS Tool Case Support Blocks 916Protects left engine case while servicing inner balancer bearings, Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case, Keeps case level when using bearing pullers...

JIMS Tool Installation Inner Ball Bearing 915Designed for early or late Beta® cases, Accurately and safely install the inner balancer bearing mounted in the left engine case, All done on a work bench without using an arbor press, Made in the U.S.A.

FEULING OIL PUMP CORP. Tool Crankshaft Runout 9015Makes for a great display to show and explain to customers the condition of their crankshaft, Simplifies and speeds up the process of checking pinion shaft run out, Quickly and accurately measures gear...

JIMS Tool Oil/Filter Inspection Cutter 935Use to inspect oil filter for any damaging particles that may be trapped in filter, Locks down filter for a clean cut around filter base, Fits filters up to 5-1/2" diameter, Made in the U.S.A.

JIMS Tool Thread Chaser Society of Automotive Engineers 933An inexpensive way to clean up threads on frames or other parts that have been powder-coated or painted, Not for cutting new threads, Made in the U.S.A.

JIMS Tool Valve/Guide Installer 7Mm 938Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals, Made in the U.S.A.

JIMS Tool Valve/Guide Remover 7Mm 937Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals, Made in the U.S.A.

JIMS Tool Balancer Shift Alignment 952Takes the guesswork out of setting up your balancer shaft sprocket and chain alignment, Made in the U.S.A.

JIMS Torque Plate Twin Cam '99-'17 Original Equipment 951Torque plates must be used when boring or honing late-model aluminum cylinders, Simulate running stress conditions, Come with instructions, Made in the U.S.A.

JIMS Tool Balancer Shaft Bearing Remover/Installer 957Complete kit safely removes and installs outer balancer bearing on the chain guide support plate, Also installs the new balancer bearing and counter balancer shaft on Twin Cam 96", 103" or 110" "B"...